The front door for our homes will be located below the home on the center spar of the floating TriPod base. You will enter through the door and then walk up a spiral staircase which will take you right into the living area of the home. This is a quick video showing the process of […]

Here is a quick video that shows how we protect the metal of the center dock from corrosion. This dock will go around one of the outer spars on the floating TriPod base. You can see two of these docks that are installed on our first floating TriPod base.The first step is to remove all […]

We recently finished up the mold for the hot tub that will sit on one of the side spars of the floating TriPod base if you decide to add it. It is designed to have cushions around the edge to sit and then the hot tub itself will be in the middle. We won’t cover […]

Now that the roof is in place, it is time to get working on the ceiling and everything that will go in between the roof and the ceiling. One crucial piece is the supports that will help hold the ceiling panels in place.We are making the supports in a grid pattern similar to what would […]

This is a quick video showing how we install the cross braces that will give a little extra support and strength between the outriggers and the center spar on our floating TriPod base. The brace itself is made from a simple steel tube. We then have a template that we place on the tube to […]

This outer ring for the EcoPod roof is made up of 28 smaller sections which are then put together into four pieces made up of seven sections each. These smaller sections are much easier to manufacture than a larger section so this process worked out pretty well. We assembled all of the pieces on the […]

Grant is back with another update from the factory. This time he is showing us some of the progress on the hot tub that will be an option to add to one of the three side spars on the floating base.The hot tub will sit on the top of the circular side spar, so naturally, […]

The crew have been building a large arm that we can use with our fiberglass spray gun to help make the process go faster. This arm will be great for spraying large areas during production.A good example of how this will help during production is when we have to make the huge “bowl” for the […]

Part 2 of our process to get the EcoPod roof put together went fairly smoothly with only a few expected difficulties. Installing these roof sections was not easy and they take quite a bit of work to get properly fitted together, but we got the job done at the end of the day. Placing this […]

Our homes are made primarily of fiberglass sections that are formed in molds. When we take those sections and put them together, we have to lay sections of woven fiberglass fabric out and then roll a resin on them to harden them. This is very time-consuming and can be difficult when working in tight spaces.This […]

This video shows the process of how we install the four quarter sections of the EcoPod roof. We made these four sections with a mold and finally started to put them into place. These pieces are large and cumbersome to deal with but with a bit of muscle and help from our telehandler, we were […]

This is a quick video to show how we are going about installing the second half of the kitchen/patio floor in our SeaPod prototype.We learned quite a bit after spending almost a full day installing the first half, so we attacked this one from a different direction. The first time involved a lot of manhandling […]

As we move closer to getting the EcoPod prototype finished up, Grant wanted to share a bit of the process of installing the outer ring of the roof. This roof is made of 28 sections which are installed together to make a big donut shape. Once the outer ring is in place we will install […]

Most parts of our homes are built by using molds built from 3D printed designs to shape fiberglass panels that we will then fit together. Some pieces, however, use a different method. One example of that is the bathroom sink area of the EcoPod.The video below shows the process of how we are making the […]

We spent quite a long time producing the prototype molds for the SeaPod here at the factory, in fact, some parts took nearly two years to get right. These prototype molds are what we used to make the first prototype, but they won’t be what we use when the SeaPod goes into full production.We have […]

The EcoPod roof has multiple uses and features. The most obvious is that it is a roof, it protects the people inside from the sun and rain, just like any normal roof. This roof will also have a slight cone-shape that will act as a funnel to collect rainwater to be used within the home.Those […]

The SeaPod windows are just absolutely massive. They have been a massive challenge to manufacture but we finally have done what we started out to do three years ago. Now that we have found a company that has successfully manufactured the windows, we have to find a way to get them to the factory here […]

We are creating 3D printed coral habitats with our new 3D printer that is able to print a clay material as opposed to a traditional plastic filament. The clay is safe for the ocean and provides a porous surface to help encourage coral growth.One of the things about working with clay is that it has […]