Building the initial prototype, Alpha Blue, was a journey of commitment and challenges. Learnings from modularity, new roof design with solar panels, expanded floor space, and LED lights mark the evolution to Alpha Deep. Embracing sustainability, adaptability, and innovation, the EcoPod’s ongoing journey promises a future where human settlement transcends land constraints. Each step demanded […]

Here we have a look at the mold for the dinner chairs that will be on the Wazebo. The Wazebo will have a large table in the middle with bench seating around the outside that is perfect for lounging. When you want to sit at the table to eat, we will have these movable chairs […]

Welcome inside our Seapod flagship model, as we are finishing work on the interior of the shell itself. We are really into a “might fit” time right now because there will be differences between this prototype and the production model. We are live from the Pod’s living room where we are putting the last touch […]

Grant is back inside the factory to give us a look at part of the process of building the Wazebo floor. Like a lot of aspects of the Pods, these floor sections are made out of fiberglass that is formed in molds. The mold makes one-quarter of the floor at a time and since the […]

“Welcome home”! That’s what we will say…once we will be done with the Pods’ entrance. We’re not there yet, but we are definitely making great progress so it should come sooner than later. We are now working on the center dock, or in other words, what will become the porch of your future home. Specifically, […]

It’s “Crunch” time for the wazebo benches! We are very excited to put the final touch on these key elements of our Pods for one of their most important uses: relaxing. But for now, we only have a few days left before launch on the water! If you follow our promising progress, you know that […]

We are making some good progress on the dock and Grant is back to tell us a little bit about it. This dock is pretty big, at about 3×8 meters. The structure of the dock is concrete but the buoyancy comes from the core which will be mostly foam. We have a large steel mold […]

Grant has another factory update – the mold for the Wazebo seating area is almost ready to go! We built the plug and then used that to make this mold. Once this mold is ready, we can take it off of the plug and do the finishing work needed to get it finished. We can […]

Up until now, the interior of the SeaPod prototype has just had the inner surface from the mold process. Of course, we needed to add the interior walls and so far, that process has been moving along nicely. The SeaPod is curvy and these walls are no different. These walls are made of a honeycomb […]

We recently finished up the mold for the hot tub that will sit on one of the side spars of the floating TriPod base if you decide to add it. It is designed to have cushions around the edge to sit and then the hot tub itself will be in the middle. We won’t cover […]

This outer ring for the EcoPod roof is made up of 28 smaller sections which are then put together into four pieces made up of seven sections each. These smaller sections are much easier to manufacture than a larger section so this process worked out pretty well. We assembled all of the pieces on the […]

We spent quite a long time producing the prototype molds for the SeaPod here at the factory, in fact, some parts took nearly two years to get right. These prototype molds are what we used to make the first prototype, but they won’t be what we use when the SeaPod goes into full production.We have […]

We have been working on the EcoPod roof for the past few weeks and we are now finishing up production on the final section of the inner disk. The video below shows the process that the crew has to do to release each section from the mold. These 1.3cm fiberglass sections have an extremely tight […]

We are back at the factory for a quick update from Grant about the progress of the EcoPod roof. This will be a functional roof in a few different ways so we are really excited about it. The team has been making quick progress and it is starting to take shape.The roof is going to […]

The SeaPod will have an absolutely massive panoramic window in the living room that will provide stunning views of the outside world. These windows were a serious challenge to design and engineer due to their size and their curved shape, but as with every challenge we have faced, we found a way to make it […]

We have spent the last almost two years designing, building, and perfecting the prototype molds for the SeaPod. These are the molds that we have been using here at the factory to build the first prototype of the SeaPod. The prototype molds also acted as a form of research and development for our production molds […]

Grant is here today to give us an update from the factory. We can see the mold for the bottom of the SeaPod, which will be assembled with the roof, and of particular importance in this video is the mold for the sides of the SeaPod. These side pieces are essential in that they connect […]